Injection Molder

From Open Source Ecology
Jump to: navigation, search


Injection Molder
   Home  |  Research & Development  |  Bill of Materials  |  Manufacturing Instructions  |  User's Manual  |  User Reviews    78px

Overview

Rick Sparber's Modified Gingery Injection Molder

The Injection Moulder enables fast production of highly repetitive/homogeneous parts such as plugs, switches, knobs, handles, etc.

The embodied energy + wear & tear of milling a set of metal mould plates for production has historically limited this process to parts produced on a scale of many thousands or even millions, however, using a 3D Printer and a Foundry it may be possible to cast cheap recycled-aluminium moulds in order to produce repetitive parts on the order of hundreds or more, which would otherwise cause excessive wear on a 3D Printer.

With a Shredder, the injection moulder is a core component for recycling old thermoplastics that would not be suitable for Fused Filament Fabrication type 3D Printing, such as polyethene and polypropene, which form a majority of waste plastic flows.

Template:Video:Injection Molder

Detailed Description

The Injection Moulder consists of a melt-chamber fed with chipped recycled plastic and/or pellets of virgin plastic feedstock, heated to a controlled temperature by a heater cartridge, heating resistor or some wound nichrome wire, and forced through a nozzle into a mould by a piston fitting the melt-chamber. For large moulds requiring high pressure, a piston can be driven by a motor using a leadscrew, but for small batches/parts a hand-operated lever is fine.

A simple Arduino-programmed ATMega microcontroller with a potentiometer (analogue knob) or 7-segment display & tactile switches (digital) input driving a high-voltage relay with low-frequency PID, would easily suffice for temperature control.

The melt chamber/cylinder can be made from a smooth steel pipe if you have a piston to fit it (e.g. the one shown in the video above), or from a block of aluminium with hole drilled through it using a drill press (e.g. the one in Gingery's book, and shown in Rick's document) with a 1cm thick steel rod for a piston (as can be salvaged from many discarded inkjet printers). The latter could be made with greater heating efficiency and lower material use by casting aluminium into a desired rounded shape and then reaming the melt-chamber hole to a smooth bore.

Nozzle production follows much the same theory as any RepRap 'hot-end' - having a lathe makes this much easier.

Almost any structural materials could be used for the injection moulder's frame, from recycled lumber to welded steel sections. As noted in Rick Sparber's document, attention needs to be paid to properly constraining the piston in a hand-operated lever system, so as to avoid any out-of-axis force bending the piston out of shape.

Product Ecology

Product Ecology
Template:Injection Molder
From Uses Creates Enables

Components

  • Piston
  • Cylinder
  • Heater
  • Controller
  • Nozzle
  • Lever or Leadscrew
  • Moulds
  • Plastic Parts

OSE Project Status/Schedule

The injection moulder project is currently in research phase. Subject matter experts are encouraged to contact us.

See Also

References


The Global Village Construction Set
Habitat CEB Press Cement Mixer Sawmill Bulldozer Backhoe
Agriculture Tractor Seeder Hay Rake Well-Drilling Rig
Microtractor Soil Pulverizer Spader Hay Cutter Trencher
Bakery Oven Dairy Milker Microcombine Baler
Industry Multimachine Ironworker Laser Cutter Welder Plasma Cutter
CNC Torch Table Metal Roller Rod and Wire Mill Press Forge Universal Rotor
3D Printer 3D Scanner CNC Circuit Mill Industrial Robot Chipper Hammermill
Drill Press Induction Furnace
Energy Power Cube Gasifier Burner Solar Concentrator Electric Motor Generator Hydraulic Motor
Steam Engine Heat Exchanger Wind Turbine Pelletizer Universal Power Supply
Nickel-Iron Battery
Materials Aluminum Extractor Bioplastic Extruder
Transportation Car Truck

Imprimante 3D Scanner 3D Extracteur d'Aluminum Pelleteuse Four à Pain Presse à balles de paille Extrudeuse à bioplastiques Bulldozer Voiture Presse BTC Betonnière Broyeur à marteaux Imprimante de circuits électroniques Table de découpe numérique Trayeuse Perçeuse à colonne Moteur électrique Gazogène Faucheuse Râteau à foin Moteur hydraulique Fourneau à induction Bras robotisé Poinçonneuse Découpeur Laser Laminoir à plaques Microcombine Microtracteur Multimachine Batterie Ni-Fe Machine à granulés Torche plasma Power Cube Presse hydraulique Laminoir à barres et fils de fer Pulvérisateur de terre Scierie Semoir Concentrateur solaire Roto-bêche Moteur à vapeur Echangeur de chaleur Tracteur Fraiseuse de tranchée Camion Alimentation électrique universelle Rotor universel Poste de soudure à l'arc Plateforme de forage de puits Eolienne

Key Design Planning Prototype Almost done Full Release