Tobbens Folgertech Kit Assembly Log

From Open Source Ecology
Jump to: navigation, search

Introduction

This document is created to try to document a 3D printer build as detailed as possible, to facilitate the development of D3D Workshops. The starting point is an unboxed Folgertech Prusa i3 (see Tobbens_Folgertech_Kit_Unboxing_Log) and the instructions located at Prusa_i3_Modular_Build_Video containing script, Module Assembly Oder 3 module videos module 1, module 2, module 3, as well as time lapses of overall assembly, frame build and extruder slide build. The Folgertech build manual is also used.

Table and kit.JPG

Method

Build steps are performed calmly with no hurry.

No tools are prepared or planned beforehand, so time consumption for getting tools is included.

Nothing on the work-table is touched unless time is recorded. I've tried to avoid solving problems in my head or thinking about specific build steps when the stop watch is not running, so that also the thought work required is captured in the recorded times. Recording thought work with a stop watch is of course impossible to do perfectly.

Stop watch is stopped only while writing this log, taking pictures, eating and going to the toilet.

A "step" usually contained

  1. Start stop watch
  2. Identify what to do, possibly by planning and/or reading documentation
  3. Do it
  4. Stop stop watch

Since documentation was consulted only once per step, the size of a build "step" was defined and limited by Tobben's working memory. Hence the number of assembly steps in the log below translates to a rough count of documentation lookups/planning pauses. We say a rough count because there were some deviations from this rule.

Reliability Of Recorded Numbers

Tobben has assembled many RepRaps before, and also read the Module Assembly Order document prior to this logged assembly. Reading took ~10 minutes. Quantifying the relative advantage of previous RepRap experience is very hard, but recorded times should be at least be doubled for novices.

Log

Time order Module Activity Time consumed Time consumed, accumulative Instruction Resources Used Comment Image
1 Bottom Frame 1 Removing tape from 2020s 0:05:46 0:05:46 None Fiddly
Remove tape from 2020s.JPG
2 Bottom Frame 2 Identifying which beams to use 0:04:55 0:10:41 Folgertech's Build Manual Unable to find this info on OSE wiki
3 Bottom Frame 3 Watching Module 1 Video 0:01:30 0:12:11 module 1 video Good video
4 Bottom Frame 4 Very roughly sorting Hardware Bag contents 0:02:20 0:14:31
Rough sorting kit hardware.JPG
5 Bottom Frame 5 Assembly of 8 first L-brackets 0:16:01 0:30:32 module 1 video Assembly manual: Fill all L-bracket holes with mount screws before inserting into 2020s. Don't use L-shaped hex-key since mounting relies on 2020s lying down flat.
L brackets in place rotated.JPG
6 Bottom Frame 6 Confusion regarding the T-nut and screw sizes. 0:16:54 0:47:26 module 1 video, Folgertech's Build Manual M4 and M5 T-nuts look very similar.
M4 M5 Tnuts.JPG
7 Bottom Frame 7 Assembly of left Y-rod bushings and corner brackets in middle of front beam 0:09:01 0:56:27 module 1 video Say in assembly manual: Corner bracket hole sizes are big enough to be able to put T-nut through. Kit comment: M4 screw heads should have been bigger. T-nut and washer fiddling took lots of time.
Corner bracket with washer.JPG
8 Vertical Frame 1 Assembly and Mounting on Base Frame 0:33:33 1:30:00 module 1 video Because of poor corner bracket quality, M4x8 screws are _almost_ too short, and power supply mounting gets very fiddly.
Right leg of frame.JPG
9 X-axis 1 Faulty Assembly of X-carriage Linear Bearings 0:09:41 1:39:41 module 2 video Linear bearings mounted with smooth rod running through. This did not alone prevent the faulty mounting. Kit comment: This error possible because of bad print quality.
Faulty X assembly 1.JPG
10 X-axis 2 Faulty Assembly of X-carriage Linear Bearings 2 0:10:25 1:50:06 Space for Linear Bearing is too short. Cut out more space by hand with knife. This is weak design since bearing fixation along X-axis is unimportant, so making a tight fit serves no purpose. Process made harder by smooth rods being very far from straight. Video showing bad gliding
Faulty X assembly 3.JPG
11 X-axis 3 Assembly of X-carriage Linear Bearings 0:04:59 1:55:05 More manual cutting needed to get Linear Bearings into their tracks.
Faulty X assembly 2.JPG
12 X-axis 4 Mount Linear Bearings Into X-idlers 0:03:02 1:58:07 module 2 video Use paper to wipe off linear bearings, the stuff they're soaked in is not healthy to get on fingers.
X Linear Carreage.JPG
13 X-axis 5 Mounting X idler bearings 0:02:47 2:0:54 module 2 video Took a guess at which screw to use.
X Idler Bearings.JPG
14 X-axis 6 Mounting X Belt pulley and X-motor 0:08:43 2:9:37 module 2 video A fair amount of guesswork to find the correct screw length.
IMG 1102.JPG
15 X-axis 7 Fitting together idlers, carriage and linear rods 0:01:48 2:11:25 module 2 video
Beltless X Axis.JPG
16 X-axis 8 Thread X-belt 0:04:29 2:15:54 module 2 video Slight print error in X-carriage made fastening belt harder. Pushed in place with flat screwdriver.
X Belt Thread.JPG
17 Z-axis 1 Preparing Z-motors 0:06:50 2:22:44 module 3 video M3x11 screws...
Prepared Z Motors.JPG
18 Z-axis 2 Preparing filament guide 0:02:03 2:24:47 module 3 video 1 min extra from tool change hex key -> previously unused screw driver -> hex key
Below Right Z Motor.JPG
19 Z-axis 3 Preparing Z-motors' T-nuts 0:03:14 2:28:01 module 3 video
20 Y-axis 1 Manually Enlargening Linear Bearing Holders 0:13:20 2:41:20 Once again, print error/extremely tight fit by design had to be adjusted with a knife to make linear bearings fit.
Once again.JPG
21 Y-axis 2 Threading zip-ties and figuring out how to place printed bearing holders 0:04:39 2:45:59 Folgertech Build Manual
22 Y-axis 3 Drilling out printed bearing holders' 3mm holes 0:04:59 2:50:58 Bad prints eat time budgets for lunch. This time, a squeezed out first layer was our enemy, preventing M3 screws from gliding freely.
Bad prints eat.JPG
23 Y-axis 4 Fastening Y Linear Bearings 0:09:47 3:0:52 Folgertech Build Manual page 8 First use of 5 mm spanner. Took extra time because of that.
First use of 5 mm.JPG
24 Y-axis 5 Soldering and taping heat bed wires 0:29:50 3:30:42 Folgertech Build Manual pages 9, 10 and 11 Taping wires alone took ~10 min. Preparing soldering equipment took ~15 min.
Taping wires alone.JPG
25 Y-axis 6 Mounting Heat Bed onto Y-Carriage 0:05:40 3:36:30 Folgertech Build Manual page 11 Instructions said M3x8 screws. 8mm was impossibly short, used 10 mm ones.
Instructions said M3x8.JPG
26 Y-axis and Frame 1 Mount Y-motor mount 0:02:54 3:39:24 Folgertech Build Manual page 4
Mount Y Motor Mount.JPG
27 Y-axis and Frame 2 Mounting Y-Carriage 0:10:40 3:50:04 Mounted left smooth rod only first. Slided in right smooth rod and secured end bushings while Y-carriage fixated the span.
Mounted left smooth.JPG
28 Y-axis and Frame 3 Mounting Y-motor 0:05:29 3:55:33 Tilt Frame sideways while mounting
Tilt Frame sideways.JPG
29 Y-axis and Frame 4 Assembling Y-idler 0:20:51 4:16:24 Folgertech Build Manual page 20 I had attached belt holder in the wrong pair of holes in the Y-carriage, so some manual aiming required. Used standard M3 nut instead of nyloc, since nyloc was fiddly.
I had attached.JPG
30 Y-axis and Frame 5 Threading Y-belt 0:04:37 4:21:01 Mount belt tensioner before tensioning the belt
Mount belt tensioner.JPG
31 X-axis, Z-axis and Frame 1 Shortening X-axis and Pushing it in place 0:07:30 4:28:31 Most time was spent shortening the X-axis. A lot of force needed.
Most time was spent shortening.JPG
32 X-axis, Z-axis and Frame 2 Tightening X-belt and right Z-rod bushing screw 0:03:30 4:32:01 Position belt tensioner here to avoid interfering with microswitch later.
Tightening X belt.JPG
33 X-axis, Z-axis and Frame 3 Mount left Z-motor 0:05:44 4:37:45 More easily done when printer is tilted. Insert threaded rod last. Secure it 1 cm below motor shaft.
More easily done.JPG
33 X-axis, Z-axis and Frame 4 Mount Right Z-motor 0:06:34 4:44:19 Hold X-axis up close to motor when tightening to assure proper alignment
Hold X axis up close.JPG
34 X-axis and Extruder 1 Mount Extruder 0:09:26 4:53:45 Folgertech Build Manual pages 18 and 19 Most time was spent screwing M3 screws 30 mm by hand because of poor print qualiy (too small M3 holes).
Most time was spent screwing.JPG
35 Endstop sensors and Frame 1 Mounting endstops 0:23:03 5:16:48 Folgertech Build Manual pages 32 and 33 Microswitch PCB and endstop holder combined differently on all three axes. Very easy to get orientations wrong.
Microswitch PCB and endstop.JPG
36 Electronics 01 Re-Mounting Power Supply 0:03:42 5:20:30 Rotate Z-endstop away to more easily access bottom screw.
Rotate Z endstop.JPG
37 Electronics 02 Attach mains voltage 0:14:44 5:31:32 Folgertech Build Manual page 35 Maybe easier to do before re-mounting power supply. All ends are tinned and bent like a hook around screw.
Maybe easier to do before.JPG
38 Electronics 03 Attaching RAMPS Power Wires 0:19:29 5:51:01 Folgertech Build Manual pages 35 and 36 All ends were tinned, which took a long time. Hooked ends to power supply.
All ends were tinned.JPG
39 Electronics 04 Attaching Acrylic Mount Plate 0:03:10 5:54:11
Attaching Acrylic Mount Plate.JPG
40 Electronics 05 Mounting RAMPS 0:08:09 6:2:20 Found no screws of correct length, used my own.
Mounting RAMPS.JPG
41 Electronics 06 Wiring Z-motors and bending RAMPS pins into place 0:06:52 6:9:12 This orientation of cables is reflected in firmware.
The orientation of cables.JPG
42 Electronics 07 Wiring Y-motor 0:05:27 6:14:39 Took 2 min longer because I've mounted Y motor with contacts facing backwards. Getting the connector into the motor was a tight fit.
Took 2 min longer.JPG
43 Electronics 08 Wiring X-motor 0:02:20 6:16:59 Ran out of zip-ties. Had to go get new ones.
Ran out of zip.JPG
44 Electronics 09 Wrapping Extruder cables in cable guide 0:05:11 6:22:10 Wrap them all at the same time. This step should have been postponed until after soldering longer fan-cables.
Wrap them all.JPG
45 Electronics 10 Connecting 22 gauge wires for Extruder Fan to 12 V 0:05:42 6:27:14 This step should have been done together with step 38, "Attaching RAMPS Power Wires". Would have saved ca 2 min.
This step should have been.JPG
46 Electronics 11 Soldering fan wires to 22 gauge 12 V wires and wrapping 0:13:30 6:40:44 This step included some unwinding of cable-guide, preparing soldering iron, stripping wires, finding cable shrink (not included in kit). With a connector or longer fan cables in the first place, this step would have been 2:30.
This step included some unwinding.JPG
47 Electronics 12 Connecting Hot end to RAMPS 0:08:31 6:49:15 Folgertech Build Manual page 30 Heater element connectors were tinned. Heater cables a little tricky to strip, took ~1 min more than stripping plastic cables.
Heater element connectors were tinned.JPG
48 Electronics 13 Connecting Bed Wires to RAMPS 0:09:33 6:58:48 Folgertech Build Manual page 29 Bed heater wires were tinned. These are the most important ones to tin and secure tightly! The instructions from Folgertech told the user to plug the black bed wire into a RAMPS port marked with "+". This felt so wrong, I just couldn't do it. The bed is just acting as a resistor, so it would work either way.
Bed heater wires were tinned.JPG
49 Electronics 14 Connecting Endstops 0:15:30 7:14:18 Folgertech Build Manual pages 33 and 34 The Folgertech guide has a bug in it. Near bottom of page 33, it says "There are 6 rows of pins". Every other following statement with pin counts assumes 7 rows of pins. There are really 1 _column_ of four I2C pins and 6 columns of end stop pins. These are ordered like Z_max,Z_min,Y_max,Y_min,X_max,X_min. Therefore, step 23.10 in the Folgertech manual also is a bug, since we have a X_max endstop, not a X_min one. These bugs took 10 min to get straight.
The Folgertech guide has a bug.JPG
50 Electronics 15 Final check and Connecting Power 0:02:46 7:17:04
Final check and Connecting Power.JPG
51 Software 1 Booting D3D Configured Porteus 0:02:00 7:19:04 D3D_Live_ISO#Computer_Models_Verified_to_Boot Had to specify /dev/ttyACM0 in Pronterface's drop down menu before pressing "connect".
Pronterface port dropdown.JPG
52 Print 1 Pre-flight Check 0:25:00 7:44:04 Started a Python script for future automation of this process, published here.
53 Print 2 First Print 0:15:21 7:59:25
First Folgerprint.JPG

Results

There were 53 steps with time consumption ranging from 1:30 to 33:33.

Time Saving Trough Participant Training

The most cognition-intensive module was the electronics with 15 steps/documentation lookups, taking a total of ~2 hours. Having one person learn these steps and do them several times could maybe save in many minutes (1 h?) per printer on average.

Time Saving Through Kit Quality

  1. Errors in printed parts (steps 9, 10, 20, 22, 34) took ca 47 minutes of extra time.
  2. If the extruder fan had long enough cables to reach the power supply in the first place, ~6 minutes would have been saved.
  3. In step 43, ca 1 minute could have been saved if Folgertech had included more zip-ties.

In sum, these four kit perfections would have saved almost 1 hour.

Time Saving Through Better Instructions/Documentation

  1. Confusions that could have been avoided by better marking and sorting of kit hardware (steps 2, 4, 6, 14, 29, 40) took ~1 h.
  2. Ca 12 minutes were spent re-heating a soldering iron (steps 37 and 46).
  3. Ca 5 minutes were spent unwrapping and re-wrapping the cable guide (step 46).
  4. Ca 10 minutes were spent sorting out a bug in Folgertech's documentation (step 50).

In sum, an instructor could have saved in 1 h 27 min distributed over 9 different steps.

Time Saving Through Shortening Individual Assembly Steps

By sorting the build steps on Time Consumed, we get a top 5 time consumers as follows:

Step Name Step Time Mitigations to Speed Up
Assembly and Mounting Vertical Frame on Base Frame 0:33:33 Get M4x10 screws to mount power supply instead of M4x8
Soldering and taping heat bed wires 0:29:50 Lump build steps together so that all soldering is done at once, possibly by instructor/host before workshop.
Pre-flight Check Before First Print 0:25:00 Automate somehow. Possible by making a custom interface in Printrun (custom Pronterface GUI).
Mounting endstops 0:23:03 Skip Z-endstop. Bed probe makes it superflous. Possibly cut away endstop-PCBs (their only function is flashing a LED). Integrate endstop mount in X-idler printed part. Make Y-endstop holder less error-prone by symmetry.
Assembling Y-idler 0:20:51 Get larger M4 washers. Use standard M3 nut instead of nyloc. Possibly pre-assemble sandwich of brackets, bearings and washers.

Notice that since a "step" is subjectively defined, it's not guaranteed that the longest build step holds the greatest potential for time saving. Also, the mitigations mentioned in the table above only concerns small changes in the assembly process of a Folgertech 2020 Prusa i3. It might be more time saving to use a completely different 3d printer design, but this is not captured here.

Afterthoughts

First of all, the printer works. See video of first print.

However, the assembly is an error-prone process. There are hundreds of common and uncommon mistakes that are easy to do but hard to debug, making the build a risky endeavor for novices.

Pitfall Examples

Y-belt mount point that allows belt to come in from the wrong angle:

Y belt not straight.JPG

This would make the pulley work along the leg of an ever-changing triangle instead of a straight line, and big prints' dimensions would be wrong.