File list
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description |
|---|---|---|---|---|
| 22:55, 27 October 2009 | Plasma cutter and motor controller.JPG (file) |  |
375 KB | |
| 18:28, 27 October 2009 | Gooped up.JPG (file) |  |
234 KB | |
| 18:24, 27 October 2009 | Thread locker applied.JPG (file) |  |
180 KB | |
| 16:52, 27 October 2009 | Loctite 243 and rail.JPG (file) |  |
228 KB | |
| 21:08, 23 October 2009 | S5000697.JPG (file) |  |
2.43 MB | |
| 21:05, 23 October 2009 | Smaller 703.JPG (file) |  |
394 KB | |
| 21:04, 23 October 2009 | Smaller size 702.JPG (file) |  |
288 KB | |
| 21:01, 23 October 2009 | Sparks 1.jpg (file) |  |
486 KB | |
| 21:00, 23 October 2009 | Sparsk 2.jpg (file) |  |
449 KB | |
| 20:59, 23 October 2009 | Tt team 2.jpg (file) |  |
780 KB | |
| 20:53, 23 October 2009 | TT team photo.jpg (file) |  |
760 KB | |
| 20:42, 23 October 2009 | Cutting.jpg (file) |  |
510 KB | |
| 21:48, 16 October 2009 | Space frame and bricks in all their glory.JPG (file) |  |
2.33 MB | |
| 21:45, 16 October 2009 | Another picture of space frame joint, less fuzzy.JPG (file) |  |
2.21 MB | |
| 21:39, 16 October 2009 | How the joints look on space frame.JPG (file) |  |
2.08 MB | |
| 19:00, 16 October 2009 | More space frame goodness 3.JPG (file) |  |
2.31 MB | |
| 18:52, 16 October 2009 | Space frame pieces 2.JPG (file) |  |
2.3 MB | |
| 18:43, 16 October 2009 | Space frame lengths drilled.JPG (file) |  |
2.3 MB | |
| 16:35, 8 October 2009 | Plasma cutter with modification.JPG (file) |  |
2.21 MB | |
| 16:28, 8 October 2009 | Back of motorcontroller.jpg (file) |  |
2.06 MB | |
| 16:23, 8 October 2009 | Wired up and nowhere to go.JPG (file) |  |
2.41 MB | |
| 16:14, 8 October 2009 | Wire extensions.JPG (file) |  |
2.19 MB | |
| 16:06, 8 October 2009 | Xylotex ends, previously connected to the motor controller.JPG (file) |  |
2.13 MB | |
| 15:53, 8 October 2009 | Wire extenders to crimp.JPG (file) |  |
2.05 MB | |
| 16:17, 7 October 2009 | Binary encoded wires.JPG (file) |  |
2.02 MB | |
| 16:00, 7 October 2009 | Soldered and wood screws.JPG (file) |  |
2.09 MB | |
| 15:33, 7 October 2009 | Project Box with holes.JPG (file) |  |
2.15 MB | |
| 15:22, 7 October 2009 | Control box parts jumble.JPG (file) |  |
2.41 MB | |
| 15:16, 7 October 2009 | Wires all attached plasma cutter filter.JPG (file) |  |
2.18 MB | |
| 15:12, 7 October 2009 | Put back torch plasma trigger filter.JPG (file) |  |
2.07 MB | |
| 15:03, 7 October 2009 | Solder the leads.JPG (file) |  |
2.11 MB | |
| 15:00, 7 October 2009 | Phone jack input plasma.JPG (file) |  |
2.17 MB | |
| 19:01, 30 September 2009 | Circuit diagram opto relay.jpg (file) |  |
42 KB | |
| 13:47, 26 September 2009 | First Square.JPG (file) |  |
1.9 MB | |
| 14:46, 24 September 2009 | AQV252G.pdf (file) |  |
69 KB | |
| 01:50, 24 September 2009 | Main board.JPG (file) |  |
1.22 MB | |
| 01:41, 24 September 2009 | Mc14066bcp datasheet.pdf (file) | |
149 KB | |
| 01:28, 24 September 2009 | Signal filter plasma cutter.JPG (file) |  |
1.18 MB | |
| 23:58, 23 September 2009 | Pilot arc powerplasma circuit board.JPG (file) |  |
1.22 MB | |
| 23:33, 23 September 2009 | Put it on the rail.JPG (file) |  |
1.23 MB | |
| 23:27, 23 September 2009 | Attaching the spring.JPG (file) |  |
1.19 MB | |
| 23:14, 23 September 2009 | Almost done with motor.JPG (file) |  |
1.23 MB | |
| 23:05, 23 September 2009 | Motor with gear and spring.JPG (file) |  |
1.23 MB | |
| 23:00, 23 September 2009 | Finished motor assembly and carriage.JPG (file) |  |
1.22 MB | |
| 22:49, 23 September 2009 | Ten and two.JPG (file) |  |
1.2 MB | |
| 22:44, 23 September 2009 | Its got bunny ears.JPG (file) |  |
1.21 MB | |
| 22:39, 23 September 2009 | Fuzzy pic of washers and screws.JPG (file) |  |
1.09 MB | |
| 22:20, 23 September 2009 | All the parts for motor.JPG (file) |  |
1.23 MB | |
| 20:25, 23 September 2009 | Grinded screws.JPG (file) |  |
1.24 MB | |
| 20:20, 23 September 2009 | Screws all in a row.JPG (file) |  |
1.21 MB |
